Pmr Help!1!1

[Paul.L]

Can someone help when ever I turn on my pmr it shoots by itself and then wont shoot after that.I think its the microchip .

And also does anyone know where I can fit the Rf chip in the pmr with the pulse hopper thanks alot.

[danman2008]

Your trigger might be stuck in.

[Paul.L]

I tried ajusting it already. Same problem

[danman2008]

Check out the board. Make sure everything is connected tight and nothing is out of order.

[Paul.L]

Everything is perfect its just once it turns on boom a shot fires by itself then it wont shoot.

[danman2008]

Well then call Proto. I really dont believe you checked over the board and the trigger because that would be the source of your problem unless your battery is dead. Then you would just be retarded. Just put the chip in the gripframe, or follow some instructions.

[Paul.L]

I'm calling proto tommorrow and I checked it and the local shop checked it. And the rf chip cant fit in the gripframe but I know people have it in their. And its a brand new battery.

[bryce moulton]

sounds like your micro switch is sticking to me.
but if it turns on and emedietly fires on its own theres something wrong with the board. because if its the trigger being fired or held down when you turn it on it shouldnt fire it should go into programing mode... sounds like something is ither wrong with your microswitch to me.

[KTaDD x 23]

Call Proto to have it fixed, or bring it to your Proshop.

For the RF chip, don't try to put it in. If you break it, theres no refunds. Send it in to Draxxus and theres a quick turnaround.

[I <3 Paintball]

Look at like page.. 5-7 of the manual. It says that if the trigger sensitivty is too low, it can begin to shoot, and etc... Read up on that, it should explain it well

[ootsk]

Are there balls in it? If you turn it on, it won't fire without balls unless you press the second button to turn off the eyes. I'm guessing the gun has been empty during these tests. That means the trigger is not the problem....it's the board.

[I <3 Paintball]

Paul. Look at the trouble shooting in the back of the manual. It explains your problem exactly. Has something to do with trigger sensitivity too low, or the trigger needs to be adjusted.

That, or the eyes were on w/ no balls

[Paul.L]

Well it wasnt in the back and the eyes didnt turn off when there was a ball so it would randomly shoot. The problem was I had a bad board. So it wasnt the trigger or microswitch.

[I <3 Paintball]

Well it wasnt in the back and the eyes didnt turn off when there was a ball so it would randomly shoot. The problem was I had a bad board. So it wasnt the trigger or microswitch.
[/b]

Your POSITIVE it was the bad board? You read the troubleshooting carefully first, right? Its prob cus the trigger was adjusted to tightly, with little pull back room.

[Paul.L]

Your POSITIVE it was the bad board? You read the troubleshooting carefully first, right? Its prob cus the trigger was adjusted to tightly, with little pull back room.
[/b]


100% positive because i tried ajusting the trigger.

[I <3 Paintball]

100% positive because i tried ajusting the trigger.
[/b]

Did you even try adjusting the trigger sensitivity electronically? Not the manual, allen adjustment, but the configuration, electronic adjustment mode?

[Metric]

You have a year warenty....

[acko]

Can someone help when ever I turn on my pmr it shoots by itself and then wont shoot after that.I think its the microchip .

And also does anyone know where I can fit the Rf chip in the pmr with the pulse hopper thanks alot.
[/b]

i promise its ur trigger. u prolly screwed one of the adjustment screws too far in. it says it in the manuel just read that and fix it

[flexi]

don't rez threads this guy probably found the problem and fixed it a long time ago

[F-N-U]

And the rf chip cant fit in the gripframe but I know people have it in their[/b]
those people have UL frames or some other aftermarket frame... i dont think there is room for one in the stock frame


EDIT: SOB... i was tricked... i just looked at the date on the last couple posts as i read down the page :lol:

[bballryand316]

those people have UL frames or some other aftermarket frame... i dont think there is room for one in the stock frame
EDIT: SOB... i was tricked... i just looked at the date on the last couple posts as i read down the page :lol:
[/b]

Oh well. Again, I shall be right on the Rail, and you will be wrong. :D

RF Chip fits in the stock frame. The UL Frame is smaller, and way less room.

If you haven't fix it by now, simply revert all settings to stock.

For the RF Chip - Check PbNation - There's one on there somewhere.

[F-N-U]

Oh well. Again, I shall be right on the Rail, and you will be wrong.[/b]
thats great <_<... gimmie 1 week once it gets here & ill know EVERYTHING about um

[bballryand316]

thats great <_<... gimmie 1 week once it gets here & ill know EVERYTHING about um
[/b]

Like it's 3.2 pound weight? :lol:

[F-N-U]

i found out why they say that on EVERY SITE tho... thats the shipping weight... they should really say that

[K1nGKooPaPaintball]

the noly thing im thinkin about is that probaly ur trigger is screwed too much in

[maldon007]

Kind of an old thread dude.