omen

[evilomen2.0]

What is the best hopper for the evil omen 2.0? I am willing to spend any kind of money, i wish that the q loaders would work with the omen, but they will ruin the feed system

[Evilpaintballer888]

well , any view loader evlution will do fine. I think reloader b's. Ricochet apaches too. Halo won't work with it though.

[thevoiceinurhd]

I know someone who has a q-loader Omen, but they modified their cam arms. Reloader B's and Halos have jamming problems with the cam arms, but if you modified them they would work. Eggs do work though, and only a handfull of people have problems with halos, reloader b's feed on every shot so there might be a problem. I'll try to find out how to do the mod for you.


Heres the Cam arm mod curtesy of BPS at pbn

Thought I'd show you the easy mod I made to use the Q-loader. By adding another outer cam (short fat one) I was able to use the Q-loader at reduced windings. Once I was confident it was working fine, I glued the outer 2 cams together, making it even stiffer. Works with full 16 winds now. A Q-loader with full winds will drop test over 75BPS!! And that's thru 8" of hose and an elbow! I have also used the new cam arrangement with a V35 Halo and it worked fine at all settings. My PDchip only goes 25 max and with the halo on 35 it still did not bypass the cam jamming the gun.

The extra cam arm was like $7 or so from RJskateworks and he shipped it the day I ordered it!


Step 1. Remove allen screw holding feedtube assembly. Swing assembly up out of the way. Remove small allen screw holding cam arm rocker cover.

Step 2. Remove 2 phillips screws holding cam arms onto the rocker. Make note of inner cam arm position as if you flip it later screw holes between cam arms will not line up with rocker.

Picture shows open cam assembly and final positions of 3 cam arms. (not glued yet.)

http://i33.photobucket.com/albums/d56/Texiam/CamMod1.jpg


Step 3. Screw 2 outer cam arms (short fat) together. This will ensure the holes are lined up later after applying the glue. If you try to line them up by eye, your screws will not fit thru. There is very little room for error.

Step 4. Apply small amount of Super Glue Gel to end of cam arms. Only cover about 50% max and only from where cam arm gets fatter to the end. If you glue the entire thing end to end it will not have enough flex to perform correctly. Super Glue Gel works better than contact cement becuase you can dissolve it later with nail polish remover if you make a mistake. The glued cam arms will be far stiffer than one or even 2 non-glued just screwed together.

http://i33.photobucket.com/albums/d56/Texiam/CamMod2.jpg

Step 5. Make sure glue is 100% dry before putting all 3 cam arms together. YOU DO NOT WANT THE FIRST CAM TO STICK TO THE OUTER !! Screw all 3 cam arms back onto rocker using 2 small phillips screws. The original screws are plenty long enough to hold. Replace cam rocker cover with small allen screw. Flip feed tube assembly back down and secure with large allen screw.

http://i33.photobucket.com/albums/d56/Texiam/CamMod3.jpg

Step 6. Looking down the feed tube, cycle marker WITH NO AIR. Make sure the outer 2 cams are catching on the stop allowing the first cam to push into the breach. Also make sure all 3 cams return far enough to allow next paintball to drop with out resistance.

http://i33.photobucket.com/albums/d56/Texiam/CamMod4.jpg


You're done, no go kick some ***!!
Better yet, walk up to a Halo B owner and shoot your marker UPSIDE DOWN!!! Then challenge him to try that. You can now lay down and shoot out of a bunker with your barrel only 1" off the ground. People don't expect you down that low on a bunker!

Point of note: I have the Q-loader at a slight downward angle. If you try to mount it perfectly straight on the Detonator it will block the collar, stopping any adjustment. Once you have the Detonator adjusted and locked in you can readjust the q-loader if you want.

[evilomen2.0]

Pretty sweet setup with the Q loader, thinking of trying it out myself. If that doesnt work then what will I have to do to get a reloader b to work with my 2.0

[thevoiceinurhd]

The Cam arm mod shown above, which will work good with halo b, reloader b, and Q-loader. Could a Mod sticky this, possibly?